That's one of my favorite mods on your jeep you need to find that and post it.
Printable View
Updated pics............
https://theultimatejeep.com/images/i...08130826-1.jpg
https://theultimatejeep.com/images/i...08130826-1.jpg
https://theultimatejeep.com/notfound.png
https://theultimatejeep.com/notfound.png
https://theultimatejeep.com/notfound.png
https://theultimatejeep.com/images/i.../11/base-1.jpg
https://theultimatejeep.com/notfound.png
https://theultimatejeep.com/notfound.png
I installed my new toy, Motion Computing LS800 tablet.
https://theultimatejeep.com/notfound.png
https://theultimatejeep.com/notfound.png
Getting Nat Geo TOPO! program next.
Ok, I finally got around to mounting my new wheels.
https://theultimatejeep.com/images/i...11111518-1.jpg
https://theultimatejeep.com/images/i...11111518-1.jpg
https://theultimatejeep.com/images/i...11111701-1.jpg
https://theultimatejeep.com/images/i...11120821-1.jpg
Bought a Air Compressor from Harbor Frieght for 58.00 included a 2 year
replacement warranty.
https://theultimatejeep.com/images/i...age_1795-1.jpg
Central Pneumatic 66399
This compact, high volume 30 amp air compressor will inflate a car tire in just 3 minutes, providing fast, reliable service at a moment's notice.
Maximum pressure: 150 PSI
- Air delivery: 1.35 CFM @ 40 PSI, 1.14 CFM @ 70 PSI, and 1.05 CFM @ 90 PSI
- Includes 25 ft. coiled air hose, pressure gauge, and 10 ft. battery cables with clamps
- Gearless direct drive for quiet operation
- Thermal overload protection
- Cast alloy pump casing with cooling fins
- Anti-vibration rubber feet
- 12 volt, 30 amp motor
:)
Now I wont be yelled at for not airing down!
And then i sold it......:(
taking space for future use.......
A couple new mods.....
I got a hinged license for the front plate. I am going to mount my block
Heater cord here and a 12 v outlet.
https://theultimatejeep.com/images/i...ontplate-1.jpg
https://theultimatejeep.com/images/i...1/11/top-1.jpg
Open
https://theultimatejeep.com/images/i.../11/open-1.jpg
I ran a 10ga wire to the front, followed the existing wiring harness. I add this plug.
This is a low draw system, not starting or trying to fast charge the battery.
Right now, this is my wifes old battery. I will replace with 2 storage type batteries.
https://theultimatejeep.com/images/i...0650_507-1.jpg
I plug my trailer battery in here. Would have been nice to use the 7 prong plug for the trailer lights but it
was too late.
For quite a while, I wanted a plug for jumper cables instead of the usual clip here,
clip there, and fight the cables. Here is what i did....
I bought 2 ANDERSON,50A ,CONNECTOR KITS, SB50A, 600V,BLACK, on ebay. I paid less than $8 for the pair.
https://theultimatejeep.com/images/i...nnectors-1.jpg
I soldered the ends of the cables to the battery clamps. I didnt like that
the wire ends were clamped on.
https://theultimatejeep.com/images/i...83252529-1.jpg
https://theultimatejeep.com/images/i...07/clamp-1.jpg
I put the connectors in the vices
https://theultimatejeep.com/images/i.../07/vice-1.jpg
Filled with silver solder
https://theultimatejeep.com/images/i...1/07/map-1.jpg
I used my map gas torch on these
https://theultimatejeep.com/images/i...oldering-1.jpg
Side View of Plate
https://theultimatejeep.com/images/i...84252529-1.jpg
Lifted Plate - you can see where I drilled through to run the cable.
Routed it along side the bumper and attached to an existing harness.
https://theultimatejeep.com/images/i...86252529-1.jpg
Attached copper lugs to cables
https://theultimatejeep.com/images/i...87252529-1.jpg
Red and Black wire zip tied to wire
https://theultimatejeep.com/images/i...7/Cables-1.jpg
^^^ Thats a pretty cool idea!