How to install SA super sliders

Writing the install guide and pics.

Your going to want to put the rails on a jack to get it lined up.

Note: if yours are powder coated you might not want to put to much of the jeeps weight on them while being supported from underneath. Diffidently use something to protect the coating while putting them in place or jacking them into place.

https://theultimatejeep.com/images/i..._5580JPG-1.jpg

Jack the sliders in place and triple check it's location. Make sure it's not to far forward or to far to the rear. Once your happy jack the Jeep up some like this to apply pressure to the rails and make room for the jack stands. This step is not necessary though you can mark your holes for drilling at this point if you so wish.

https://theultimatejeep.com/images/i..._5581JPG-1.jpg


Set the jack stands under the sliders then lower the jeep onto the sliders so that the jeep is being held up by the sliders. This spreads the weight and pressure out across the sliders ensuring they are tight and in place.

https://theultimatejeep.com/images/i..._5582JPG-1.jpg

Now take a paint marker and mark your holes.

https://theultimatejeep.com/images/i..._5583JPG-1.jpg


https://theultimatejeep.com/images/i..._5584JPG-1.jpg


Now take a sharp center punch at tape the center of your hole. This will help keep your drill bit from dancing around.
https://theultimatejeep.com/images/i..._5585JPG-1.jpg

https://theultimatejeep.com/images/i..._5586JPG-1.jpg


Now take a smaller bit then the 9/16 bit for the nutsert and drill your smaller hole. This will also help keep your larger bit from dancing around and ensure accuracy.
https://theultimatejeep.com/images/i..._5590JPG-1.jpg


Now take the 9/16 drill bit and drill your final holes. Use steady and easy pressure do not force the bit this will bend the thin metal and may cause the nutsert not to seat properly. I recommend you just buy a new bit for this so it's sharp and little pressure will be needed to get threw.
https://theultimatejeep.com/images/i..._5591JPG-1.jpg


Clean up your holes and make sure no metal shavings are left behind to interfere with the nutsert seating.
https://theultimatejeep.com/images/i..._5592JPG-1.jpg

This is a nutsert and acts the same as an anchor you would use for wood. The ribbed section you see is the section that will crush and grip the metal. To setup the nutsert for installation take the longest bolt you were sent and put a washer on it then put the nut you were sent and put that on then add another washer then thread the nutsert on the bolt. Then push this hole assembly into the hole you drilled.

https://theultimatejeep.com/images/i..._5579JPG-1.jpg


Put an 1\2 wrench on the bolt to hold it in place and help stabilize the nutsert.
https://theultimatejeep.com/images/i..._5594JPG-1.jpg

Put a wrench and socket also a 1\2 and I recommend using a 1\2 set for more leverage. You must tighten the bolt while putting enough pressure inwards to keep the nutsert tight in the hole. It will be tough going at first as you crush the nutsert. As your going you will notice you can wiggle the setup while wrenching it down then once the ribs in the nutsert give way it will become a lot easier to turn the bolt. Once you see the setup tighten up and stop wiggling the bolt will get hard to turn again which means you close. Tighten to about 15 FT LBS and remove the bolt and check the nutsert to see if its crushed all the way. It is not recommended that you use any power tools to install the nutsert. The risk of over tightening the nutsert is high with power tools so stick to doing by hand. If you do use an impact take the bolt out often and visually check the nutsert until you get a feel for how much it takes to crush the nutsert and get use to where to stop.
https://theultimatejeep.com/images/i..._5597JPG-1.jpg

This is what it will look when its crushed all the way. You do not want to over tighten the nutsert you will risk it spinning and loosing its grip. If this happens apply a small tack to it with a welder and grind flat that will hold it in place.
https://theultimatejeep.com/images/i..._5595JPG-1.jpg

For the bolts on the front and rear up by the doors you just have to open the doors and use a wrench to tighten these bolts up.
https://theultimatejeep.com/images/i..._5598JPG-1.jpg

Under neath this is what it will look like when your done.
https://theultimatejeep.com/images/i..._5599JPG-1.jpg


https://theultimatejeep.com/images/i..._5600JPG-1.jpg


https://theultimatejeep.com/images/i..._5601JPG-1.jpg


https://theultimatejeep.com/images/i..._5602JPG-1.jpg

I totally for got to post this sorry about that someone had troubles installing there sliders yesterday this may of helped but it's posted now LOL


Note: if yours are powder coated you might not want to put to much of the jeeps weight on them while being supported from underneath. Diffidently use something to protect the coating while putting them in place or jacking them into place.

wow dude, great write up!

Nice write up. Maybe someday ill be able to use it.

Quote:

---

Originally Posted by BonesWK

wow dude, great write up!

---

Quote:

---

Originally Posted by 07JeepXK

Nice write up. Maybe someday ill be able to use it.

---

Thanks guys and I added a note to the process.

Great write up, photos and techniques !! I'm just now getting some time to start reading the Forum again and hopefully contributing occasionally. My sliders have arrived ! Now the long wait to find time to install them. It took me 6 months to relocate my backup camera and I just completed it today.. looking fwd to this project ! Thanks again for the great post !!

Nice, Sal - I'm sure this will be very helpful to many in the future.