To mount the Transfercase Select Switch, a couple holes need to be drilled on the bottom of the Shifter storage area. And a hole provide for the Switch Plug to plug into the rear of the Switch.
I think I can make a template for these holes.
To mount the Transfercase Select Switch, a couple holes need to be drilled on the bottom of the Shifter storage area. And a hole provide for the Switch Plug to plug into the rear of the Switch.
I think I can make a template for these holes.
06 Red Jeep XK 3.7L V6 QT1, RC 2" with 1/2", 1-1/4" Wheel Spacers, Rubicon Moab Rims, Grabber AT2 LT265/70-17, Rocky Road Supersliders, Fastman Throttle-body, K&N Cold Air Filter, JBA Headers, Front Tow Hooks, 2" receiver front & rear, Wired for winch front & rear, ARB Onboard Air, Trans Temp Gauge, Aux Trans Cooler, Sport Roof Crossbars, Skid Plates, RS5010 Rear Shocks, JKS 2034 Front & 2001 Rear Disconnects
Here is the Transfercase Selector Switch mounted and plugged into the stock wiring harness. My XK had this wiring in place. But it needs to be modified to work with my controller.
Last edited by cmdr jim; 05-08-2012 at 08:28 AM.
06 Red Jeep XK 3.7L V6 QT1, RC 2" with 1/2", 1-1/4" Wheel Spacers, Rubicon Moab Rims, Grabber AT2 LT265/70-17, Rocky Road Supersliders, Fastman Throttle-body, K&N Cold Air Filter, JBA Headers, Front Tow Hooks, 2" receiver front & rear, Wired for winch front & rear, ARB Onboard Air, Trans Temp Gauge, Aux Trans Cooler, Sport Roof Crossbars, Skid Plates, RS5010 Rear Shocks, JKS 2034 Front & 2001 Rear Disconnects
Here is the modified wiring, Pins 1, 2 & 3 cut and wired to run to my controller. Please note I have soldered and heat-shrink-ed all connections and sealed of cut ends of wiring harness that will not be used. I have run these wires along the stock wiring harness using tie-wraps. All changes under the console are complete.
Next will be making up the panel to mount the two modules and relays that will power and control the Transfercase Motor, that will be going in under the passenger side rear seat.
After that running the wires between the two areas, adding the key switch and testing the Transfercase before actually installing it. One step at a time.
Last edited by cmdr jim; 05-08-2012 at 08:27 AM.
06 Red Jeep XK 3.7L V6 QT1, RC 2" with 1/2", 1-1/4" Wheel Spacers, Rubicon Moab Rims, Grabber AT2 LT265/70-17, Rocky Road Supersliders, Fastman Throttle-body, K&N Cold Air Filter, JBA Headers, Front Tow Hooks, 2" receiver front & rear, Wired for winch front & rear, ARB Onboard Air, Trans Temp Gauge, Aux Trans Cooler, Sport Roof Crossbars, Skid Plates, RS5010 Rear Shocks, JKS 2034 Front & 2001 Rear Disconnects
Its looking good. Cant wait to see more pics!
2007 4.7 Liter XK | Front Modified OME HD Lift | Rear 4" Superlift | JBA UCA's | Rusty's Rear Adjustable Track Bar | Rysty’s Adjustable Upper and Lower Rear Control Arms w/Heim Joints | Mickey Thompson Classic III 17x9 Wheels | 315/70R17 Goodyear Duratracs | Airflow Snorkel | Flowmaster 40 Series Muffler | Superchips Flashpaq | Mopar Skids | 4xGuard Belly Guard | American Rebel Rear Diff Cover | Rear Powertrax No-Slip | Front Electronic Locker | Rear Heat/AC Delete
Heck of a mod man!
I hope to have the wring completed this weekend. I plan on putting the transfer-case in the back of the XK and just wiring it in before actually swapping in it. I can then check out my wiring and programming before the actual install. Installation is planned the weekend of the 19th if all goes well.
Keep in mind, I'm working on this slowly, a couple hours here a couple there.
06 Red Jeep XK 3.7L V6 QT1, RC 2" with 1/2", 1-1/4" Wheel Spacers, Rubicon Moab Rims, Grabber AT2 LT265/70-17, Rocky Road Supersliders, Fastman Throttle-body, K&N Cold Air Filter, JBA Headers, Front Tow Hooks, 2" receiver front & rear, Wired for winch front & rear, ARB Onboard Air, Trans Temp Gauge, Aux Trans Cooler, Sport Roof Crossbars, Skid Plates, RS5010 Rear Shocks, JKS 2034 Front & 2001 Rear Disconnects
Another step closer. Under the rear seats of the Commander there are to small areas covered by a carpeted lid. On the driver side is were the FDCM and Parking Control Module would go. On the passenger side, mine is empty and it provides a perfect place to mount the relays and voltage regulators. Next step is to ground the panel, provide power and final connecting of the wires to the controller under the dash.
06 Red Jeep XK 3.7L V6 QT1, RC 2" with 1/2", 1-1/4" Wheel Spacers, Rubicon Moab Rims, Grabber AT2 LT265/70-17, Rocky Road Supersliders, Fastman Throttle-body, K&N Cold Air Filter, JBA Headers, Front Tow Hooks, 2" receiver front & rear, Wired for winch front & rear, ARB Onboard Air, Trans Temp Gauge, Aux Trans Cooler, Sport Roof Crossbars, Skid Plates, RS5010 Rear Shocks, JKS 2034 Front & 2001 Rear Disconnects
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote