I agree with MAtt, when I installed my k&n I noticed a huge problem with water getting in so I made a custompieces to go in behind the grill and under the intake to protect it, Ill post up the link..
I agree with MAtt, when I installed my k&n I noticed a huge problem with water getting in so I made a custompieces to go in behind the grill and under the intake to protect it, Ill post up the link..
2K6 Limited Jeep Green Metallic/Saddle Brown Leather XK HEMI QDII Old Man Emu HD Suspension w/ Fox Emulsion 2.0 Rear Shocks 1.5" SpiderTraxx Wheel Spacers 265/70 GoodYear MTRs w/Kevlar True Dual Exhuast w/IMCO 50 K&N 63 CAI Diablo 91/Performance Transmission Tuned SA Belly Skid MOPAR Gas Tank Skid, Transfer Case Skid, Suspension Skid Front Tow Hooks 6k HID Lows/3k Fogs
2K6 Limited Jeep Green Metallic/Saddle Brown Leather XK HEMI QDII Old Man Emu HD Suspension w/ Fox Emulsion 2.0 Rear Shocks 1.5" SpiderTraxx Wheel Spacers 265/70 GoodYear MTRs w/Kevlar True Dual Exhuast w/IMCO 50 K&N 63 CAI Diablo 91/Performance Transmission Tuned SA Belly Skid MOPAR Gas Tank Skid, Transfer Case Skid, Suspension Skid Front Tow Hooks 6k HID Lows/3k Fogs
Yeah I would take Matt's advice as well. I intended to do this and actually removed it myself. There was no benefit that is noticable. I ended up doing what Matt did and just replacing the intake tube as well as the air filter and keeping the stock airbox. This provides more then enough air then stock at the same time keeping water out.
If you are looking for an intake, try AFE - it uses the bottom 3/4 of the stock airbox. Thus keeping the design. Though my only complaint with it, is it does not remove the big air silencer that sits on top of the engine..
Ryan ---- 2006 WK 4.7 QDII <- Click for Garage
2.25" RR Lift - Front Bilstiens - Rear OMEs - 32" Wildpeaks - Saguaro 4x Shackles - Tail Light Guards - AFE intake - Rola - Exhaust
Twitter Facebook ---- Chive On
I noticed an air intake temperature of 8 degrees lower just by removing the shield the OP is talking about, and that is an average value (at highway speeds). YMMV if you are using a stock intake system. If you do off roading and splashing through rivers I would not reccomend it but it sure as crap wouldn't save you from hydrolock as is..Although I use an AFE intake (full kit) that does not totally seal the charge to draw air 100% from that location. Also my afe intake totally removes the big silencer and is a very nice peice, like bones said it uses the lower half of the factory airbox in which it clips onto..
Ryan ---- 2006 WK 4.7 QDII <- Click for Garage
2.25" RR Lift - Front Bilstiens - Rear OMEs - 32" Wildpeaks - Saguaro 4x Shackles - Tail Light Guards - AFE intake - Rola - Exhaust
Twitter Facebook ---- Chive On
Probably due to the fact I have the 5.7 as opposed to the 4.7.. Also my iats were probably lower because with my intake, air is not 100% pulled from the front like stock, so removing the shield helped force some cool air in.. A stock intake pulls from that same location 100% so there would not be any gains or lower temps from removing this peice. Just to clarify
There are currently 1 users browsing this thread. (0 members and 1 guests)