Hmm sounds nothing like my flowmaster. From the sound I was guessing you had the v6
Hmm sounds nothing like my flowmaster. From the sound I was guessing you had the v6
2007 4.7 Liter XK | Front Modified OME HD Lift | Rear 4" Superlift | JBA UCA's | Rusty's Rear Adjustable Track Bar | Rysty’s Adjustable Upper and Lower Rear Control Arms w/Heim Joints | Mickey Thompson Classic III 17x9 Wheels | 315/70R17 Goodyear Duratracs | Airflow Snorkel | Flowmaster 40 Series Muffler | Superchips Flashpaq | Mopar Skids | 4xGuard Belly Guard | American Rebel Rear Diff Cover | Rear Powertrax No-Slip | Front Electronic Locker | Rear Heat/AC Delete
2006 Jeep Commander
4.7, QTII, 2'' RC, 245/75/17 Duratracs, Black Rock 908B wheels, 35% tint, Magnaflow exhaust, Navigator offroad lights
So the Commander took the back burner for a bit due to some budget cutbacks....however im going hit up Harbor Freight this week and start to work on a light bar. With any luck im hoping to have it all complete for around $100.
Id also like to get some recovery shackles since i lack them on the front or rear currently.
Also if funds permit, hoping to pick these up after Christmas. Thoughts?
http://www.quadratec.com/products/92613_2020_07.htm
Last edited by NCCommander; 11-19-2012 at 12:44 AM.
2006 Jeep Commander
4.7, QTII, 2'' RC, 245/75/17 Duratracs, Black Rock 908B wheels, 35% tint, Magnaflow exhaust, Navigator offroad lights
Check with adam.... I think you need 1/4" spacers up front for the black rocks because the hit the calipers.
I have the Black Rock 997 steel wheels with the same specs and needed 1/4 inch spacers up front to clear the front caliper brackets. Those might need the spacers too.
Last edited by 07JeepXK; 11-19-2012 at 04:43 AM.
2007 4.7 Liter XK | Front Modified OME HD Lift | Rear 4" Superlift | JBA UCA's | Rusty's Rear Adjustable Track Bar | Rysty’s Adjustable Upper and Lower Rear Control Arms w/Heim Joints | Mickey Thompson Classic III 17x9 Wheels | 315/70R17 Goodyear Duratracs | Airflow Snorkel | Flowmaster 40 Series Muffler | Superchips Flashpaq | Mopar Skids | 4xGuard Belly Guard | American Rebel Rear Diff Cover | Rear Powertrax No-Slip | Front Electronic Locker | Rear Heat/AC Delete
Ill check with him, with a 0mm offset and 4.5'' backspacing it shouldnt. I know theres at least 1 WK on Jeepforum running them without spacers....
Im guessing youre Adam haha
Ill just have to test fit one before i mount a tire on them and see....
2006 Jeep Commander
4.7, QTII, 2'' RC, 245/75/17 Duratracs, Black Rock 908B wheels, 35% tint, Magnaflow exhaust, Navigator offroad lights
2007 4.7 Liter XK | Front Modified OME HD Lift | Rear 4" Superlift | JBA UCA's | Rusty's Rear Adjustable Track Bar | Rysty’s Adjustable Upper and Lower Rear Control Arms w/Heim Joints | Mickey Thompson Classic III 17x9 Wheels | 315/70R17 Goodyear Duratracs | Airflow Snorkel | Flowmaster 40 Series Muffler | Superchips Flashpaq | Mopar Skids | 4xGuard Belly Guard | American Rebel Rear Diff Cover | Rear Powertrax No-Slip | Front Electronic Locker | Rear Heat/AC Delete
Looking at the picture, it seems where the wheel mounts to the rotor/wheel bearing assembly is deeper then my black rocks. If you look the lug nuts go farther into the wheel. That would make a huge difference making 1/4 inch wheel spacers not needed
2007 4.7 Liter XK | Front Modified OME HD Lift | Rear 4" Superlift | JBA UCA's | Rusty's Rear Adjustable Track Bar | Rysty’s Adjustable Upper and Lower Rear Control Arms w/Heim Joints | Mickey Thompson Classic III 17x9 Wheels | 315/70R17 Goodyear Duratracs | Airflow Snorkel | Flowmaster 40 Series Muffler | Superchips Flashpaq | Mopar Skids | 4xGuard Belly Guard | American Rebel Rear Diff Cover | Rear Powertrax No-Slip | Front Electronic Locker | Rear Heat/AC Delete
There are currently 1 users browsing this thread. (0 members and 1 guests)