• Welcome to TheUltimateJeep.com! We're a friendly group of Jeep enthusiasts who love to talk about Jeeps, answer questions and have fun. We specialize in Jeep Commanders and Grand Cherokees, but welcome all Jeep models. Registration is FREE, fast and simple: join our community today!

Rear diff leaking - pinion seal

jcoulter

Legendary member
Joined
Jun 14, 2010
Messages
110
Reaction score
0
Location
Quad Cities, IL
I noticed some fluid under my Commander a few days ago. It appears that the rear pinion seal is leaking. There is NO play in the driveshaft so the bearing is not shot, yet.

I've never messed around with this kind of problem. Can anyone tell my how involved this seal replacement is? The axle is a Chrysler 213MM.
 
Perfect! Thanks 07. As long as the leak isn't terrible is it safe to drive until I get time to fix it, say about a week?
 
Last edited:
Yeah its fine as long as there isnt a huge puddle on the ground after you park it overnight. If its just a little wet around the seal your good to go till you can fix it.
 
Got this done last night. I did have a buddy help that has done this before. That was nice. Had to get out the 3/4" drive set for the nut.

Thanks for the help 07!
 
I was just about to post to ask if anyone other than me had to replace a rear pinion seal.
I have 18,000 miles on my 07' with the Chrysler 12 bolt rear. I just replaced the seal this past Tuesday. Everything looked real good as far as pinion angle and condition of things, The seal was just leaking. The fluid level was barely below the fill hole. I thought it would have been a lot lower with the amount of diff. fluid in my garage and on the rear diff.
Is this a common problem?
 
Yeah it's not hard to do... but you'll need a beam style in-lb torque wrench, the click-style won't work. Definitely want to make sure that you get the correct rotational resistance or else you can ruin the bearings/gears (too tight will damage the bearings, too loose will damage the gears due to pinion slop). So the price for the torque wrench is well worth it...

Money well spent: http://www.amazon.com/2955-Torque-W...ower-hand-tools&ie=UTF8&qid=1311438124&sr=1-3
 
I never ended up using a torque wrench and I really didnt go by the instructions for the whole rotational resistance. Haven't had any problems since the install and that was over a year ago.
 
That sure is an expensive risk.... glad its been working out for you though. Hopefully you got lucky and got the preload correct. If you start developing a humming noise in the rear I would recommend not letting it go too long. I've seen pinion bearings seized from too much pre-load and its not pretty. And it's always the same story "yeah its been making that noise for a while, i just thought it was the tires"

Gears and bearings are something i'm extremely careful with. And I will not install them on anyones vehicles except for mine just for the simple fact that it doesn't take much to screw it up, and when you do screw it up it's not cheap.
 
Yeah I hear you. My friend who gave me a hand doing it has been doing pinion seals for 10 plus years now and hasnt had any problems. He told me it will be fine. If the rear goes then i'll just install a dana 44 that comes in the 2wd HEMI XK's along with an ARB locker!

Also I put over 25,000 miles on a year along with off roading. I think it would have failed by now. Who knows.
 
Last edited:
Ah... well that's a completely different story! Gears are an art form.... I'm sure your friend checked the torque based on his years of experience by way of "feel". The torque method is there for guys like us who don't do gears all the time.

Its kind of like re-packing hub bearings on a vehicle... it takes some experience to learn the proper "feel" when tightening up the assembly.

I wouldn't ever advise an inexperienced person to set pinion bearing preload by feel. But someone who's very experienced is a different story.
 
Back
Top